TEAMLINK 3101 Managed Fast Ethernet Over E1/T1 Converter/Router is an intelligent converter connecting 10/100mbps Fast ethernet over fractional or full E1 circuits, that enable service providers and ISP's to supply transparent ethernet services over SDH and PDH circuits.
SNMP based element management software provides SNMP traps, status polling, and configuration download. Remote configuration is also possible through Telnet & SNMP using in-band management.
The devices are Managed inband from the Fast ethernet user port or via the TDM port. Management traffic and user Ethernet traffic are transported together on the same Ethernet flow, seperated by different VLANs, thus ensuring traffic security.
DIAGNOSTICS
Remote and local loopbacks are used for problem isolation at the physical layer.
Abuilt-in ping utility checks IP connectivity by pinging remote IP hosts.
Sends alarm notification to Manager IP addresses for the following
E1:Up/Down
Ethernet: Up/Down
Loopback : On/Off
If the ethernet error packets or collusion packets are reached more than threshold values.
ORDERING
Teamlink 3101IETH Managed Fast Ethernet Over E1 Converter
AC/DC power cord or adapter plug
HDLC / GFP-F Encapsulation
Supports CRC - 4 multiframe auto adoption
Loopback detection at WAN or E1 side and discards the ethernet packets to protect the ethernet network from jamming.
Complying GFP (G.8040, G7041/Y.1303)HDLC framing compatible with the RJ-107.
Discards over sized and undersized packets
Support STP/RSTP
The fast ethernet bridge handles 1784 bytes frames supporting for VLAN applications and other protocols requires large frame sizes
4k Mac address table learning.
Broadcast storm filtering support
Mac table display for each ethernet port and E1 side also
The teamlink 3101 ethernet to E1 converter can interoperable with third party converters with standard HDLC or GFP framing that can eliminate pair of converters for each link
Auto MDIX for auto TX/RX
4 levels of Qos based on four priority queues.
VLAN tagging and Untagging
Ethernet transmit, receive, Collision and error packets display.
Inband and out of band management access via
ASCI terminal
Telnet
SNMP
Teamview-EMS
Number of ports: One
Compliance: G.703
Data Rate: 2.048 Mbps
Line code: HDB3, AMI
Framing: Unframed
Maz Frame size: 1800 bytes
Line Impedance: 120 Ohms, balanced
System Clock: Internal or loopback timing
Diagnostics: Remote and Loopback
Connector: RJ-45
Number of ethernet Interfaces:1/2/4(Ordering time option)
Type:10/100Mbps auto negotiation
Full/half duplex, flow controls
Auto MDIX or Auto cross over facility
Compliance:Conforms to the relevance sections of IEEE 802.3 and 802.3u
Connector :RJ-45
POE :Power over ethernet is an ordering time option
HDLC compatible with RAD HDLC protocol
GFP-F (G.8040, G.7041 / Y.1303)
PWR Power status.
E1 loss E1 Loss status.
AIS AIS Status.
LOF Los of Frame.
ERR Pattern errors.
Loop Loop Indicatoin.
RAI Remote Alarm Indication.
AC: 100 to 240VAC (+/- 20%), 50 to 60 Hz
DC: -24/48 VFC (+/- 10%)
<2W
Temperature: 0-70℃/32-122 ℉
Humidity: Upto 90% non-condensing
E1 Interface: Number of ports :1
2.048 Mbps Data rate
1800 bytes of Max frame size
Connector: Rj45 (E1 Interface)
HDLC Compatible with RAD HDLC Protocol
LED Indications
In/Out band access via ASCI Terminal, TELNET, SNMP etc
STP/RSTP Support
Supports Storm filetering